IaaS/en

Introduction

This manual serves as the basis for managing virtual systems within the terra CLOUD.
The basis of an IaaS terra CLOUD always consists of a firewall. Access to the systems within a cloud can be done in several ways:

• Connection via the Technical Center (https://manage.terracloud.de/login)
• Connection via the VPN tunnel
• Connection via shared ports within the firewall

Service Informations

Please find all the information you need in the service information.
These contain, among other things, your public IP address, initial passwords, etc.
The service information can be found in the Cloud Center below the respective order, see also Service Information.

Connection to firewall

Private Cloud Strategy

Basically, every private cloud package from the TERRA CLOUD is delivered with a virtual Securepoint UTM appliance.
This starter guide serves as the basis for setting up a VPN tunnel and accessing the firewall's web interface.

Requirements for access

OpenVPN Client:

• Securepoint VPN Client - Download Link
• other OpenVPN client
• OpenVPN Client for MacOS - click here

VPN configuration file:
The VPN data for administrator access can be found in the Cloud Center below the respective order within the service information, see also Service-Information.

The point "to the download area" takes you to a central share in Terra Drive, where all your VPN data for the booked virtual environments in the Terra Cloud is located. The prerequisite for this is the access data for your Drive NFR account.
Please note that the central share only contains the VPN data of the environments that you have booked in the Terra Cloud Center.

VLAN Requirements

Every virtual Securepoint UTM has 2x virtual network interfaces by default.
One of these communicates with the Internet, the other communicates with the systems in the package.
Since a Hyper-V VM can have a maximum of 8x network cards attached, we can provide a maximum of 6x additional VLANs.

Connect to the firewall

An existing VPN tunnel is required for the connection to the firewall.
Before establishing the connection, please check whether the standard port 1194 is enabled for VPN connections on your local firewall.
If port 1194 is blocked, establishing the VPN tunnel will fail.

Initial setup of the VPN connection in the Securepoint VPN Client

• Install the respective VPN client, in this example we are assuming the Securepoint VPN client.
• Open the VPN client and click the gear at the bottom right to open the settings menu..
  

• In the context menu under Source file, click on the three dots to select the source file that was previously downloaded from the Cloud Portal.

• Select the opvn file from the previously extracted zip file and click “Import”.
• Optionally, the configuration can be assigned a name under “Import as:” under which the configuration will later be visible in the VPN client.
• Use the arrow button to start establishing the VPN connection

The required initial access data is:
User: ssluser-admin
Password: ChanTroFar93!

Connection to the firewall web interface

After the VPN connection has been successfully established, access the following address in any browser:
https://<firewall IP address>:11115

The IP address of the firewall was assigned by you when ordering the environment and can be accessed subsequently in the Cloud Center
can be viewed below the respective order within the service information, see also Service Information.



The required initial access data is:
User: fwadmin
Password: Terra001

Initial access to the firewall web interface

Note:
The WebGUI has changed visually since firmware version 12.6.2.
However, with a few exceptions, all points are still called the same, so you can continue to follow all the steps using the following instructions.

The first time you open the firewall web interface, a few things need to be done:

Assign firewall name

Please enter a firewall name, which must correspond to an FQDN, e.g. myfirewall.local.
The firewall name must not contain any umlauts, special characters or capital letters.

Then click on the Complete button.

Firmware Update

Depending on the preinstalled firmware version, you will receive a message that a newer firmware is available.
In this example we assume that version 11.8.9 is preinstalled.



This query should be answered with Yes when the environment is commissioned for the first time.
You will then receive a view of the available new firmware, which will be imported using the “Start test run” button.



In order to use the new firmware, several license agreements must be checked and accepted.


Finally, a restart must be carried out. This can take up to 5 minutes.
You can follow the restart via the console connection via the Technical Center (https://manage.terracloud.de).



After the firewall has successfully restarted and you have logged in again, the new firmware must be confirmed as the new standard firmware.

Confirm virus scanner message

If you have booked the firewall with only one vCore, you will receive a message that the number of virus scanners on the firewall has been reduced for stability and performance reasons.
This message is normal and needs to be confirmed.

Set cloud backup password

Please enter a password to back up your firewall configuration in the Securepoint cloud.
This gives you the opportunity to import the firewall configuration from the Securepoint Cloud after reinstalling the firewall.


Your firewall will then be completely set up.

Change of initial passwords

We recommend changing the initial passwords after the handover.

• In the firewall interface, open the menu item Authentication --> Users

• Click on the configuration symbol (wrench) behind the respective user and enter the new password in the Password and Confirm password fields.
• Finally, click on the save symbol at the top right.

You cannot change the user "admin".
This is an administrative account that is only used in the background for the firewall services.
Instructions and information on configuring the firewall can be found at:
http://wiki.securepoint.de/index.php/Howtos-V11

Email protection: spam filter with anti-virus package (optional)

Protection is implemented directly on the firewall included in the cloud environment.
The following options can be set:

• https://wiki.securepoint.de/UTM/APP/Mailfilter
• https://wiki.securepoint.de/UTM/APP/Mailrelay-Best_Practice

Internet protection: Content filter with anti-virus package (optional)

Internet protection is implemented on the cloud firewall in your cloud environment. The following options can be set:

• https://wiki.securepoint.de/UTM/APP/Webfilter

UMA mail archiving

Log in to Securepoint UMA

If mail archiving has been booked, a Securepoint UMA is available to you in your package.
The web interface for configuration can be accessed via the following address:

• https://X.X.X.253:11115

The prerequisite for this is a VPN tunnel that has been set up or access via a VM within the network.
The access data for this is “admin” and the password you have assigned.

Further information on configuring and commissioning the Securepoint UMA can be found at the following link:
https://wiki.terracloud.de/index.php/UMA

Role installation

In addition to providing the base operating system, certain installation scripts are carried out for VM roles that provide you with the desired functionalities,
so that you can, for example, use an Actice Directory or Windows Terminal Services directly after it has been handed over to you.
The installations are standardized so that all of the “role VMs” we roll out have the same installation and configuration status.

The pre-installation of roles can be booked up to and including Server 2019.

IaaS AD Role

After the standard VM deployment, an Active Directory is installed on the system with the domain or NetBIOS names specified in the order. It also creates an OU structure that looks like this:

• OU<DomainName>

• User
• Computer
• Groups

The AD is configured accordingly so that new user objects and computer objects are created directly in the corresponding OU.

IaaS WTS Role

If the WTS role was activated when ordering, an additional installation and configuration of Windows Terminal Services takes place after the standard VM deployment.
The terminal server is not directly licensed. To complete the licensing, please follow the steps in the relevant document -> RDS-Activation By default, the WTS services are NOT made available externally (via the Internet), but can only be accessed internally or via VPN. Access to the web access is possible via the address https://<Server FQDN>/RDWeb. To do this, name resolution must be possible from the client (either a member of the domain, access to DNS or create a corresponding entry in the HOST file). After provisioning, you log in via the user <NetBIOS>\Administrator with the corresponding password. After the initial deployment, the following applications are published:

• Office 365 ProPlus

• Excel
• One note
• Outlook
• PowerPoint
• Skype for Business
• Visio
• Word

• System Tools

• Calculator
• Paint
• Remote Desktop

Migration-VM

Differences Hyper-V generations

Under Hyper-V you can choose between Generation 1 and Generation 2 of a virtual machine.
The boot process is fundamentally different. While Generation 1 uses the older BIOS, Generation 2 is already UEFI.
It is important to specify the generation correctly when ordering, as if the wrong selection is made, the virtual machine will not boot correctly!

Advantages of Generation 1 over Generation 2

• Support for older operating systems: In order to start in UEFI mode, Windows Server 2008/R2 requires certain components of Hyper-V that are not part of the basic Hyper-V installation.
  

Some Linux operating systems have boot problems as a Generation 2 VM.

• VHD format is required
• Virtual COM ports are supported

Advantages of Generation 2 over Generation 1

• More security with Secure Boot (protection against bootloaders), TPM, Device Guard and Credential Guard
• PXE boot with Synthetic Adapter
• Faster boot or reboot time

Definition of the generation and data carrier for migration systems

The migration VMs are primarily intended to move existing IT infrastructures to the Terra Cloud.
An empty VM without an operating system is provided and FTP access is sent to the customer.
Here you have the option of uploading existing data carriers in VHD or VHDX format.

It is important that the size of the virtual disks sent in is covered by the IaaS order and that they are dynamic disks.

Example:
If a Mig-VM with 100GB system storage and 100GB data storage was ordered, this size (100GB each) may not be exceeded with the data carriers sent in.

In addition, the generation of the operating system of the virtual disks must also match the ordered generation (see Unterschiede Hyper-V Generationen).

Alternatively, we can attach the booked storage empty to the VM and you load an installation ISO onto the FTP server, which we then make available to the machine.
This means you can also operate operating systems in the cloud that we do not offer as standard and install them yourself.

package update

To do this, please select the respective customer in the center.
Then click on the desired Terra Cloud package under point Orders -> Order subitems' Orders Details and point 3 Configuration.
There you can edit the package as you wish. Such as adjusting resources, adding or canceling new VMs.

If it is an order from you (NFR), you will find it as follows:
"Gear (Settings)" -> "My Orders" -> "Orders" -> "Order Subitems" -> "Orders Details" and point 3 "Configuration"

After booking, we will process the adjustments and once completed, the package will be activated again in the Cloud Center for further processing.

Extending an additional partition (IaaS / SaaS)

If it is a package that was ordered at portal.terracloud.de (P0000XXXXX), please write an email to support@terracloud.de
Please then indicate how large the partition currently is and how much it should be expanded to.
If several additional partitions of the same size are connected to your VM, we need to specify the storage location of the partition.
Navigate to Disk Management and open the properties of the partition you want to extend. Now to the Hardware tab.
Here the location is displayed in the following format: “Bus Number 5, Target Id 0, LUN 0”.

Extension of the system partition

In order to expand the system partition, downtime is always necessary during business hours (Mon-Thurs 8 a.m. - 5 p.m., Friday 8 a.m. - 4 p.m.).

Extend Linux system partition

In the following link you will find instructions on how to extend a system partition during operation.
Please note that this represents assistance on our part and we cannot accept any liability for consequential damage.

https://wiki.terracloud.de/index.php/Linux_Systempartition_erweitern

If you want to extend the partition with "gparted", we can attach a corresponding ISO. To do this we need the package number/order number and the host name of the VM.

CPU/RAM changes of a VM

If the resources of a virtual machine need to be adjusted (RAM/vCores), a machine downtime is necessary.
You can let us know a desired date (even outside business hours).

We recommend shutting down the VM in good time before the specified date to ensure that all services can be shut down properly.
If the VM is not terminated, a shutdown is initiated. If the VM does not respond properly to the shutdown, the VM will be switched off.

Following the expansion, the VM will automatically start again.

Appointments for downtime outside of business hours can usually be accepted and implemented until 4 p.m. on the same working day.

Other

PTR-Record

The PTR record forms the reverse lookup for DNS queries.
The responsible MX record of a domain points to a public IP using an A record.

The following name resolutions are therefore created:
mail.terracloud.de -> 185.35.12.58

Many mail servers now use a reverse lookup to protect against SPAM and query the IP address at the same time.
185.35.12.58 -> mail.terracloud.de (PTR)
The PTR record therefore points to an A record via IP.

If this constellation does not exist or does not match, some mail systems may discard your emails as SPAM.

The PTR record can be set by sending a message to our support.

Connect and disconnect network addresses as a drive under Windows

You have the option of including a network address as a drive under Windows.

The integrated network address will then appear under “This PC” in the “Network Addresses” section like a normal drive and you can access it like a folder.

You can integrate a network address as a drive as follows:

• Open “This PC” in Windows Explorer. In the top left corner, next to File, expand the “Computer” submenu.
• Select the “Map network drive” option. The following window appears:

• Specify any drive letter (A: in this example).
• Enter the path, IP address or URL of the associated network address.
  

An example is: https://terracloud.de.

Now mark the option “Connect with different credentials” and press “Finish”.

• A Windows security window follows requesting login details for the website in question. Select “Save login details”,
  

if you want to retain access without having to ask for a new password when you restart the PC.

• Windows Explorer will automatically open with the drive in question.
  

You now have access to the files from the network address. The drive is also displayed under “This PC” and can also be selected there.

• You can disconnect a network drive by clicking "Computer" under "This PC" and clicking the black arrow under "Map network drive".
  
• Another menu opens with the options “Connect network drive” and “Disconnect network drive”. Select “disconnect” and the following window will open:
  

• Select the appropriate network drive and confirm your selection with “OK”.
  

Download activation after provisioning a VM

After deploying a VM, file download using Internet Explorer and Explorer is disabled by default.
You receive the error message “Current security settings do not allow downloading this file”. You can share this as follows:

• In your VM, open the Control Panel
• Select the “Network and Internet” section. There are two subtopics in this area
• Open “Internet Options”. The following window appears:

• Go to the “Security” tab and in the “Security level for this zone” section click “Adjust level”.
• Enable file download in the Download section.

• Confirm the new settings. You can now download files.

Sending

To send in the USB stick, please use the submission form.
You can find this here:

https://download.terracloud.de/files/Formulare%20&%20Zertifikate/terra%20CLOUD_Einsendeformular.pdf

Initial Setup

Connect from the system within your TERRA CLOUD environment to our FTP server using the USB dongle.
The necessary client software can be found at the following link:
ftp://ftp44.terracloud.de/SEH%20Dongelserver%20Manager/



First download the file "sehutnmanager-win-3.0.8.zip" or newer. Please pay attention to which operating system you are using.
Then unzip this file into your desired directory and run the file "sehutnmanager-win-3.0.8.exe".



Then please click on “Finish” and run the tool.



If the tool does not automatically detect your dongle, please click “Search”.



Specifying the network area is optional, but can help with the specific USB dongle search.



After searching for the USB dongle, add it using the “Add” button.
Next you will see the host name of the USB dongle server, the name of the USB dongle, the IP and the associated port.



In the last step, please click on “Activate” to activate the USB port.

FAQ

Automatically activate USB dongle after restart

Please right-click in the SEH-UTN manager on the dongle server. Then select "Activate Auto-Connect...".



In the following window, select the associated port (that has been assigned to you). Then confirm with “Ok”.

In support cases

For support requests regarding your booked USB dongle, please send us a screenshot of the SEH UTN Manager from the affected client.
Alternatively, please send us the information marked in yellow (see below).